News-Lichi Saw

2013-09

2013 China Nantong Machine Tool and Die Exhibition

Our company will participate in the 2013 China Nantong Machine Tool and Die Exhibition on September 5-7, 2013 Meeting time: September 5-7, 2013 Meeting Address: Nantong Sports Exhibition Center Person in Charge: Manager Lu 13951311115 Please pay attention to the new and old customers of our company, the new production equipment is on display, and there is a discount for the extension purchase. And warmly welcome friends from all walks of life to visit and guide, at the same time, the sales department and colleagues in various departments coordinate and handle the work well, and try to cooperate with colleagues who go to the exhibition.

2013-09-03

2013-02

Safety Operation Regulation of Metal Band Sawing Machine

A: Before work (1) Before work, protective equipment should be worn according to regulations, cuffs should be tied, and scarves are not allowed. Female workers should wear work caps and put their hair into the caps. Gloves are not allowed during operation. (2) Adjust the guide arm along the dovetail guide rail according to the size of the workpiece to be processed, and lock the guide device after adjustment. (3) The maximum diameter of the saw material shall not exceed its provisions and the workpiece shall be clamped firmly. (4) band saw blade tightness should be appropriate, speed and feed must be appropriate, saw before the test run idle 3 to 5 minutes, in order to empty the gas in the cylinder, and check whether the saw machine fault, lubricating oil is normal. (5) The adjustment of the chip removal wire brush should make the wire contact the teeth of the band saw blade, but not beyond the root of the teeth. Pay attention to observe whether the wire brush can remove iron filings. II: When working (1) The saw blade is broken during cutting. After replacing the new saw blade, the workpiece must be turned over and sawed again. The saw bow should be lowered slowly and no impact is allowed. (2) cast iron, copper, aluminum parts without cutting fluid, other need to add cutting fluid. (3) When sawing pipes or sheet profiles, the pitch should not be less than the thickness of the material. When sawing, the handle should be retracted to a slow position and the amount of feed should be reduced. (4) When multi-body sawing, a reasonable number of saws should be selected to ensure that each is in a clamped state, and the sawn material should be cleared from the band saw in time. (5) Stick to your post and observe any abnormality at any time. Pick up the saw frame or stop the car in time. (6) usually add enough lubricating oil, replace the lubricating oil in the gear box every year, and cover the guide rail and processing surface with oil when idle to prevent rust. (7) When the material is about to be sawed off, strengthen observation and pay attention to safe operation. (8) When changing the shifting position, the machine must be stopped first. Three: after work (1) After the end of the work, stop the operation of the machine tool, put the various tools used in the toolbox in an orderly manner, and place the finished products and products to be processed in the corresponding areas. (2) Daily maintenance shall be carried out on the machine tool, and spot check records shall be made in the Spot Check Table of Machine Tool. (3) Clean up the iron filings and residual materials near the working area. (4) Cut off power supply equipment such as machine tools, lighting and electric fans.

2013-02-20

2013-02

Sawing Machine Definition

A sawing machine is a machine tool with sawing action. In the traditional sense, metal sawing is often considered to be a simple cutting process. With the development of modern manufacturing industry towards high efficiency, high precision and economy, sawing, as the starting point of metal cutting, has become an important part of the processing process. Sawing can save materials, reduce the amount of secondary processing and improve production efficiency, so sawing machine, especially automatic sawing machine has been widely used in steel, machinery, automobile, shipbuilding, petroleum, mining and aerospace and other fields of the national economy.

2013-02-20

2013-02

For you to interpret the safety performance of the sawing machine

The operation of the band sawing machine is very safe, which is determined by the safety performance of the sawing machine. The following is the safety performance of the sawing machine we introduce to you: 1. Band sawing machines generally adopt the following preventive measures on site: ground carbon brushes are installed at the shaft end of the sawing machine motor to reduce the shaft potential, make the ground carbon brushes reliably grounded, and reliably contact with the rotating shaft to ensure that the rotating shaft potential is zero potential, thus eliminating the shaft current. 2, band sawing machine in order to prevent magnetic imbalance and other reasons to produce shaft current, often in the non-shaft extension end of the bearing seat and bearing bracket with insulation partition, in order to cut off the shaft current loop. 3, band sawing machine in order to avoid other motor accessories wire insulation damage caused by the shaft current, often require maintenance operators to carefully check and strengthen the wire or gasket insulation, in order to eliminate unnecessary band sawing machine motor shaft current hidden trouble. 4, the band sawing machine generally through the above processing, most of the motor shaft current is very small, has not been a substantial harm to the electric mechanism. Field practice has proved that the actual service life can be increased from tens of hours to tens of thousands of hours after the above treatment, and the effect is obvious, especially for the prevention effect of high-voltage motor shaft current, which has a positive effect on the safe production of band sawing machine.

2013-02-20

2013-02

Safety Operation Regulation of Horizontal Band Saw Machine

1, should check before processing: a, saw wheel running direction is correct. B, band saw tension is appropriate. C, whether the system pressure is sufficient. 2. According to the specifications of the material to be cut, the material should be reasonably selected: a. The tooth pitch of the saw belt. B, the appropriate amount of cutting. C, and adjust the position of the guide arm and the position of the rotary shaft end of the saw frame. 3. Test run empty first to check whether the operation is stable, whether the clamping device is reliable, whether there is noise, whether the saw band is vertical, and whether the saw frame swings. 4. When processing, strictly follow the procedure and adjust the cutting dosage according to the cutting situation. 5. A reasonable number of roots should be selected during multi-body cutting to ensure that each root is in a clamped state and the sawn material is cleared from the band saw in time. 6, stick to the post at any time to observe the abnormal timely pick up the saw frame or stop the car. 7. Remove the chips in the worktable and saw wheel box in time, and check the cleanliness and oil quantity of coolant and hydraulic oil frequently. 8, usually add enough lubricating oil, replace the lubricating oil in the wheel box every year, and add oil seal to the guide rail and processing surface when idle. 9. After the work, clean the sawing machine, add lubricating oil and cut off the power supply.

2013-02-20

2013-02

Causes of deviation of sawing accuracy

The saw blade clamped 1. the guide angle of the guide arm of the sawing machine is not perpendicular to the table of the sawing machine: Solution: Install the saw blade and adjust the bolt of the saw guide angle to make the saw blade perpendicular to the work surface. 2. the band saw blade may be loose, tighten the saw blade. 3. band saw blade is likely to wear: Solution: If the saw blade has repair value, it can be repaired. If not, replace the saw blade. 4. the band sawing machine blanking speed feed is too fast, adjust the speed control valve to make the feed speed slower. 5. the distance between the two guide arms of the sawing machine is too large, adjust the distance of the guide arm, generally 6-10cm larger than the material 6. the small bearing of the sawing machine may be damaged in the guide angle of the sawing machine, just replace the small bearing!

2013-02-20

< 1 2 3 4 5 6 >

Jiangsu Lichi SAW

Contact: Mr. Lu 86-13951311115
Telephone:86-513-85562688 86-513-85569902
E-mail:1793361753@qq.com
Website: www.jslcjc.com
Address: 350 Chenggang Road, Nantong City

Liyi SAW

Contact: Zhang Jianwei 86-13884380088
E-mail:liyisawco@gmail.com
Address: No. 539-19 Chenggang Road, Chongchuan District, Nantong City, Jiangsu Province

Jiangsu Sakoside

Contact: Wu Mingchun 86-15380568795
Telephone:86-513-85562688
E-mail:jsscdsksd@163.com
Website: www.jsksd.com
Address: 539-19 Chenggang Road, Nantong City

Website QR code

Business License

Blog