News-Lichi Saw

2013-02

Automation technology will become the key to the transformation of the band sawing machine manufacturing industry

The level of automation of band sawing machine tool products has a crucial influence on the speed and accuracy of band sawing machine, and has also become an important factor to distinguish the grade of band sawing machine. It is understood that advanced automation technology and products will undoubtedly become an important direction for the transformation of the band sawing machine manufacturing industry, and its development potential will be highlighted in this change. In the band sawing machine products, especially high-end band sawing machine products, automation technology and products almost act on every part from the control mechanism, the actuator to the measurement and feedback mechanism, and at present these applied to the band sawing machine and the band sawing machine production line of various automation products, almost all in the process of innovation. As the control center of the high-end band sawing machine, the numerical control system includes motion control, intelligent technology, self-diagnosis and other technologies. Multi-axis and multi-system numerical control devices have been developed and put into application. The control mode of servo system is gradually transitioning from regular signal type to bus type. Servo drives and motors are also developing in the direction of digitization, communication and intelligence. In this regard, many cutting-edge automation technology trends have also shown. For example, the application of linear motor and torque motor is a good example. Mazak and Mori Seiji's gantry guide rails of most specifications no longer use rolling guide rails, but use linear motors. thk's linear motors can reach a speed of 720 m/min under a load of 3000n, which cannot but be said to be a breakthrough. The torque motor can only be used in small size band saw machine, and now can be applied to more and more large size band saw machine. The maturity of these technologies is also constantly promoting the performance of band sawing machines.

2013-02-20

2010-10

Instructions for use of band sawing machine

Operational Safety Instructions 1. Check whether there are hidden dangers such as leakage before starting up 2. It is strictly prohibited to open the sawing wheel protective cover on both sides when the sawing machine is running 3. It is not allowed to touch the band saw blade in operation by hand 4. It is strictly forbidden to touch the workpiece under the saw blade operation 5. Wear protective glasses and gloves when folding and removing the saw blade 6. When replacing the saw blade, cut off the power supply of the machine.

2010-10-29

2010-10

Use and Proportion Requirements of Cutting Fluid for Band Sawing Machine

The use of cutting fluid band sawing machine: 1. In order to prevent the cutting fluid from changing due to chemical action and reducing the function, use the cutting fluid solution of the band sawing machine. 2. Pipes and pumps should be thoroughly cleaned with metal cleaning agents and prepared with tap water and clean water without heating and other treatments. 3. Regularly check whether the cutting fluid is moldy, smelly, remove debris and iron filings, and replace the cutting fluid if necessary. Band sawing machine manufacturers price cutting fluid ratio requirements: No cutting fluid, or improper type of cutting fluid, ratio imbalance, will lead to premature wear of the saw blade teeth, serious will cause heat sawing machine parts and shorten the service life, thereby increasing production costs and reducing productivity. The proportion of cutting fluid is determined according to the mechanical properties, chemical composition and sawtooth material of the material. The recommend ratio is: 5% for easy-to-cut steel and 10-15% for high-strength steel.

2010-10-29

< 1 2 3 4 5 6 >

Jiangsu Lichi SAW

Contact: Mr. Lu 86-13951311115
Telephone:86-513-85562688 86-513-85569902
E-mail:1793361753@qq.com
Website: www.jslcjc.com
Address: 350 Chenggang Road, Nantong City

Liyi SAW

Contact: Zhang Jianwei 86-13884380088
E-mail:liyisawco@gmail.com
Address: No. 539-19 Chenggang Road, Chongchuan District, Nantong City, Jiangsu Province

Jiangsu Sakoside

Contact: Wu Mingchun 86-15380568795
Telephone:86-513-85562688
E-mail:jsscdsksd@163.com
Website: www.jsksd.com
Address: 539-19 Chenggang Road, Nantong City

Website QR code

Business License

Blog